在重慶電動叉車的使用過程中，或許會發現這樣的問題，電動叉車在作業時發出很大的噪音，這是什么原因導致的呢，下面我們來分析下電動叉車噪音過大原因。

鏈條、鏈片銷軸磨損空隙過大，電動叉車上、下卡釘與叉架橫梁空隙過大。

緊固件松動，車體導輪、滾輪出現嚴重的磨損，因此也導致空隙很大。

檢查導輪、滾輪與門架的沖突翻滾空隙距離，電動叉車與叉架橫梁間的空隙是否很大，這些因素都會致使叉車廠家在使用時發生很大的噪音。

電動叉車是堆高車的種，主要動力來源于蓄電池電瓶，可是實現水平搬運、堆垛、取貨、裝貨、卸貨、揀選等過程，電動叉車蓄電池屬于一個電能轉 換成機械能的系統，當電量輸出用完的時候，要對其補充電流，否則電池將毫無作用，擱置也會對電池活性物質脫落，正常充電電流應該和叉車電瓶組成的比例，例如：48V400AH，用容量的0.14倍，可達到基本要求，超過這個電流數值，會過度充電，電池電解液揮發過快，一旦產生異味，那么叉車電池的極 板掉粉了，過度充電對容量下降是很快的，為了避免對叉車電池造成影響，我們要學會正確的充電方式，可以按照這樣來做：極板上電流分布均勻，電阻小，可 以減少充電電流的損耗，電池的析氣，筱蓋在負極正極周圍，增大電池內阻，加劇了歐姆極化，影響充電電流效率。

電池正極上活性物質的厚度與孔率，若活性物質 孔率大極板薄，有利電解液擴散，則極化作用減小，放電深度。

放電深度越深，正極活性物質Pbo ：與負極活性物質Pb 都大為減少，需要通過充電進行轉化的物質增多，即充電時參加反應的產物也多，從而提高了充電接受能力，我們不建議把充電機調到，細水長流這個道理大家 都知道，急充是很傷害電動叉車蓄電池。